Profile application to Remote Workstation Card fails
Scenario : The remote workstation card is at a factory default. You set a basic Profile in the management console and apply the Profile. The Profile application fails. If you check the management console, there is no clue as to why the Profile failed. If …
Knowledge Base Article Troubleshooting Management Management Console Remote Workstation Card
Last modified: September 19, 2023
318
How long before a PCoIP Management Console certificate expires should I replace it?
Before the PCoIP Management Console certificate can be replaced, the new certificate or the signing root CA certificate must be installed in the PCoIP Zero Client or PCoIP Remote Workstation Card certificate store. Once a PCoIP Endpoint is manged by an …
Knowledge Base Article Advisory Management Security Management Console
Last modified: September 19, 2023
291
Cannot import profile from Management Console 1.x into the PCoIP Management Console 2.x or 3.x
Answer : Importing Profiles from MC 1.x into MC 2.x is supported and documented in the user guide. Refer to the Administrators' guide for the release of the PCoIP Management Console in use. There have been a couple reports of users experiencing an issue …
Knowledge Base Article Troubleshooting Management Management Console
Last modified: September 19, 2023
286
What does "MCU not initialized" log message mean?
Problem You are unable to manage a zero client using the HP Anyware PCoIP Management Console 1.x (MC). The event logs reveal the following MCU errors: LVL:1 RC:-500        MCU :(tera_mcu_read_eeprom_bit): Cannot read from EEPROM, MCU not initialized. …
Knowledge Base Article Troubleshooting Management Remote Workstation Card Zero Clients
Last modified: September 19, 2023
279
Why Imported Profile(s) from PCoIP Management Console 1.x/2.x to PCoIP Management Console 3.x cannot be applied? Status shows skipped.
Scenario Imported a profile from PCoIP Management Console 1.x /2.x  to PCoIP Management Console 3.x where firmware 6.0.0 is the only uploaded version in Settings -> Software. Pushing the profile to PCoIP Zero Clients results in a 'skipped' status.   Cause …
Knowledge Base Article Troubleshooting Management Management Console
Last modified: September 19, 2023
268
Default HP Anyware Connector docker network conflicts with VPN network
Scenario: The default HP Anyware Connector docker network is conflicting with VPN network. When specifying the --connector-network-cidr flag during the installation of HP Anyware Connector the docker network is that same range as the default 172.x How can …
Knowledge Base Article Troubleshooting Management Setup HP Anyware
Last modified: August 7, 2023
263
Unable to start docker containers connector_cm and connector_connectorgateway during HP Anyware Connector installation
In Ubuntu 18.04.4 LTS or Ubuntu 18.04.5 LTS setting up HP Anyware Connector, if IPV6 was disabled in the vm  those 2 containers will always fail to start. During the installation or reinstallation of the HP Anyware Connector, connector_cm and …
Knowledge Base Article Troubleshooting Setup Management HP Anyware
Last modified: September 14, 2023
244
Why my HP anyware Connector (CACv2) does not connect after the recent Ubuntu 18.04 OS Nov-13-2019 Update?
The latest patch release of Ubuntu 18.04 (Nov-13 patch) will break CAM CACv2 connectivity. Affected Ubuntu 18.04 OS patch version: Nov-13-2019 release:  ubuntu-1804-bionic-v20191113 ubuntu-os-cloud ubuntu-1804-lts Recommendation: If you experience this …
Knowledge Base Article Tutorial Management HP Anyware
Last modified: September 19, 2023
243
How do I change the FQDN (Fully Qualified Domain Name) of a PCoIP Zero Client?
First, change the PCoIP name to a new name. Currently, the "PCoIP Device Name" can only be changed on an individual basis in two locations: The  "OSD--> Configuration--> Label"  tab The  "AWI--> Configuration--> Label"  tab The default format is  …
Knowledge Base Article Advisory Management Management Console Zero Clients
Last modified: September 3, 2023
232
Management Console profile is not applied to the Remote Workstation Card
Applying a Profile to a Remote Workstation Card from PCoIP Management Console will be unsuccessful if the Enable Audio setting on the Remote Workstation Card has never been enabled (default is disabled) or the Remote Workstation Card has not had the …
Knowledge Base Article Troubleshooting Management Management Console Remote Workstation Card
Last modified: November 8, 2020
228