Profile application to Remote Workstation Card fails
Scenario : The remote workstation card is at a factory default. You set a basic Profile in the management console and apply the Profile. The Profile application fails. If you check the management console, there is no clue as to why the Profile failed. If …
Knowledge Base Article Troubleshooting Management Management Console Remote Workstation Card
Last modified: September 19, 2023
323
How long before a PCoIP Management Console certificate expires should I replace it?
Before the PCoIP Management Console certificate can be replaced, the new certificate or the signing root CA certificate must be installed in the PCoIP Zero Client or PCoIP Remote Workstation Card certificate store. Once a PCoIP Endpoint is manged by an …
Knowledge Base Article Advisory Management Security Management Console
Last modified: September 19, 2023
295
Cannot import profile from Management Console 1.x into the PCoIP Management Console 2.x or 3.x
Answer : Importing Profiles from MC 1.x into MC 2.x is supported and documented in the user guide. Refer to the Administrators' guide for the release of the PCoIP Management Console in use. There have been a couple reports of users experiencing an issue …
Knowledge Base Article Troubleshooting Management Management Console
Last modified: September 19, 2023
290
Which PCoIP products support Wacom devices?
Wacom devices are supported by PCoIP using 2 different connection methods. Each connection method has it's pros and cons and the most suitable should be selected for your scenario.   Bridged USB device When using the Wacom device as a bridged USB device, …
Knowledge Base Article Advisory Peripheral Devices
Last modified: September 3, 2023
286
No warning message when VMware View Connection Server Certificate Check Mode is set to Warn if Connection may be insecure (Default)
This is expected behavior. Configured non-interactive session modes do not display VCS Warning messages in Warn if the connection may be insecure (Default) security mode.  Interactive session modes will display VCS Error messages in Warn if the connection …
Knowledge Base Article Troubleshooting Security Third Party Enhancements Zero Clients
Last modified: September 3, 2023
281
What does "MCU not initialized" log message mean?
Problem You are unable to manage a zero client using the HP Anyware PCoIP Management Console 1.x (MC). The event logs reveal the following MCU errors: LVL:1 RC:-500        MCU :(tera_mcu_read_eeprom_bit): Cannot read from EEPROM, MCU not initialized. …
Knowledge Base Article Troubleshooting Management Remote Workstation Card Zero Clients
Last modified: September 19, 2023
284
Does the Phillips Digital Pocket Memo work with a PCoIP Zero Client and VMware Horizon View?
Scenario A Philips Digital Pocket Memo (DPM) device does not operate after connecting to a PCoIP Zero Client using the USB EHCI controller (USB 2.0). Occasionally the PCoIP Zero Client unexpectedly restarts.   Cause The Philips Digital Pocket Memo device …
Knowledge Base Article Troubleshooting Peripheral Devices Zero Clients
Last modified: October 31, 2022
279
Why Imported Profile(s) from PCoIP Management Console 1.x/2.x to PCoIP Management Console 3.x cannot be applied? Status shows skipped.
Scenario Imported a profile from PCoIP Management Console 1.x /2.x  to PCoIP Management Console 3.x where firmware 6.0.0 is the only uploaded version in Settings -> Software. Pushing the profile to PCoIP Zero Clients results in a 'skipped' status.   Cause …
Knowledge Base Article Troubleshooting Management Management Console
Last modified: September 19, 2023
273
Default HP Anyware Connector docker network conflicts with VPN network
Scenario: The default HP Anyware Connector docker network is conflicting with VPN network. When specifying the --connector-network-cidr flag during the installation of HP Anyware Connector the docker network is that same range as the default 172.x How can …
Knowledge Base Article Troubleshooting Management Setup HP Anyware
Last modified: August 7, 2023
270
Why is the host PC on my VMware Horizon brokered Remote Workstation Solution unable to wake up?
Scenario When a View Connection Server brokers a workstation connection between a PCoIP Zero Client and a PCoIP Remote Workstation Card, and the host is put into any low power state (sleep, hibernate or shutdown); the client is unable to wake the host and …
Knowledge Base Article Troubleshooting Setup Performance Third Party Enhancements Remote Workstation Card Zero Clients
Last modified: September 20, 2023
265