Error: PCoIP Agent has no available licenses to launch the remote session
Symptom Remote desktops that were previously registered with HP Anyware Cloud License Server (CLS) may get the following client message when trying to connect: “Error – PCoIP Agent has no available licenses to launch the remote session.” In the Anyware …
Knowledge Base Article Advisory Troubleshooting Licensing HP Anyware
Last modified: September 3, 2023
287
Cannot import profile from Management Console 1.x into the PCoIP Management Console 2.x or 3.x
Answer : Importing Profiles from MC 1.x into MC 2.x is supported and documented in the user guide. Refer to the Administrators' guide for the release of the PCoIP Management Console in use. There have been a couple reports of users experiencing an issue …
Knowledge Base Article Troubleshooting Management Management Console
Last modified: September 19, 2023
288
What does "MCU not initialized" log message mean?
Problem You are unable to manage a zero client using the HP Anyware PCoIP Management Console 1.x (MC). The event logs reveal the following MCU errors: LVL:1 RC:-500        MCU :(tera_mcu_read_eeprom_bit): Cannot read from EEPROM, MCU not initialized. …
Knowledge Base Article Troubleshooting Management Remote Workstation Card Zero Clients
Last modified: September 19, 2023
283
After activating a renewal license on my Management Console, it is showing the old expiry date, how do I fix?
Problem: I have renewed by license for the Management Console however after deactivating and reactivating the license on my Management Console, it is showing old expiry date.  Answer : To solve this issue you need to do the following steps: 1) Return the …
Knowledge Base Article Troubleshooting Licensing Management Console
Last modified: September 3, 2023
279
Why Imported Profile(s) from PCoIP Management Console 1.x/2.x to PCoIP Management Console 3.x cannot be applied? Status shows skipped.
Scenario Imported a profile from PCoIP Management Console 1.x /2.x  to PCoIP Management Console 3.x where firmware 6.0.0 is the only uploaded version in Settings -> Software. Pushing the profile to PCoIP Zero Clients results in a 'skipped' status.   Cause …
Knowledge Base Article Troubleshooting Management Management Console
Last modified: September 19, 2023
272
Default HP Anyware Connector docker network conflicts with VPN network
Scenario: The default HP Anyware Connector docker network is conflicting with VPN network. When specifying the --connector-network-cidr flag during the installation of HP Anyware Connector the docker network is that same range as the default 172.x How can …
Knowledge Base Article Troubleshooting Management Setup HP Anyware
Last modified: August 7, 2023
268
How can I tell which monitors are connected and if a USB device is connected locally or bridged on a PCoIP Zero Client?
Answer: From your Web browser, enter the IP address of your PCoIP Zero Client. Log in to the user interface with your user credentials. (Note: Depending on your specific setup, a password may not be required.) From the Info menu, select Attached Devices . …
Knowledge Base Article Troubleshooting Display Zero Clients
Last modified: October 31, 2022
260
Why do certain large screen (>27" monitors) dual-link DVI monitors not work with the TERA 2 PCoIP Zero Clients?
Scenario When some monitors supporting 2560 x 1600 and 2560 x 1440 resolutions are power cycled with the power switch, the video may not appear when connected to a Tera2 Zero Client via dual-link DVI. This applies to: Tera2 Zero Clients running firmware …
Knowledge Base Article Troubleshooting Display Zero Clients
Last modified: November 18, 2022
251
Unable to start docker containers connector_cm and connector_connectorgateway during HP Anyware Connector installation
In Ubuntu 18.04.4 LTS or Ubuntu 18.04.5 LTS setting up HP Anyware Connector, if IPV6 was disabled in the vm  those 2 containers will always fail to start. During the installation or reinstallation of the HP Anyware Connector, connector_cm and …
Knowledge Base Article Troubleshooting Setup Management HP Anyware
Last modified: September 14, 2023
246
How do I change the FQDN (Fully Qualified Domain Name) of a PCoIP Zero Client?
First, change the PCoIP name to a new name. Currently, the "PCoIP Device Name" can only be changed on an individual basis in two locations: The  "OSD--> Configuration--> Label"  tab The  "AWI--> Configuration--> Label"  tab The default format is  …
Knowledge Base Article Advisory Management Management Console Zero Clients
Last modified: September 3, 2023
249