How do I enable and disable the PCoIP Zero Client session disconnect CTRL-ALT-F12 key sequence?
Enable When using a PCoIP Zero Client to connect to HP Anyware, Amazon Workspaces or VMware Horizon View the Ctrl-Alt-F12 shortcut is enabled by default. This setting can be configured via the AWI or PCoIP Management Console. When using a workstation with …
Knowledge Base Article Tutorial Session Management Management Console Zero Clients
Last modified: September 3, 2023
1717
How do I reset the configuration parameters entered on my PCoIP Zero Client or PCoIP Remote Workstation Card?
Answer: There are four ways to reset the PCoIP Zero Client to default settings which are described below. The PCoIP Remote Workstation card (also known as a PCoIP host card) has one reset procedure also described below. Some network information will be …
Knowledge Base Article Tutorial Management Setup Remote Workstation Card Zero Clients
Last modified: September 3, 2023
1622
VMware View Client with dual Virtual NICs unable to connect to virtual desktop
Scenario A VMware View Client with dual virtual NICs configured may not be able to connect to the virtual desktop.  Note: this article does not apply to PCoIP Zero Clients. Dual Virtual NICs Configured on the View Client   Cause If the client has been …
Knowledge Base Article Troubleshooting Performance Third Party Enhancements Zero Clients
Last modified: September 3, 2023
1621
Troubleshooting artifacts in a PCoIP Session
Problem During a PCoIP Session artifacts are appearing on the screen. The artifacts may stay or slowly disappear.   Cause and Resolution There are may reasons artifacts may appear on the screen. Some may be source issues such as the application or …
Knowledge Base Article Troubleshooting Performance Display HP Anyware Remote Workstation Card Zero Clients
Last modified: September 3, 2023
1550
How can I determine the frame rate at a PCoIP protocol client?
Answer: There are a multiple ways to determine the frame update rate displayed at the PCoIP Zero Client.    Note: the frame rate displayed at the client this may be different than the source display frame rate when in a congested network environment.  Log …
Knowledge Base Article Tutorial Performance Remote Workstation Card Zero Clients HP Anyware
Last modified: September 3, 2023
1491
How do I optimize the Windows 7 desktop experience settings to reduce PCoIP session bandwidth?
Answer: On a Microsoft Windows 7 machine, make the following change to the Windows optimization settings: Start > Computer > System Properties > Advanced System Properties > Performance Settings button > Adjust for best performance . Alternatively, you …
Knowledge Base Article Tutorial Performance HP Anyware Zero Clients
Last modified: September 20, 2023
1480
Why can I not establish a PCoIP connection through my Palo Alto firewall?
Scenario With the PCoIP Transport Header enabled and using a Palo Alto firewall: PCoIP Zero Clients fail to open a session and show a black screen. The PCoIP Zero Client must be rebooted to get out of this state. Soft clients will only be able to connect …
Knowledge Base Article Troubleshooting Performance HP Anyware Remote Workstation Card Zero Clients
Last modified: December 9, 2022
1460
How much latency does PCoIP technology add to the remote system?
The latency added by PCoIP technology to a remote system is related to the time to encode (compression) and decode (decompression) for the PCoIP protocol, which depends on the implementation. Total end-to-end latency is determined by OS latency and …
Knowledge Base Article Advisory Performance HP Anyware Remote Workstation Card Zero Clients
Last modified: July 28, 2023
1354
Why do I hear pops and crackles or dead air in my PCoIP session when connecting with a PCoIP Zero Client?
This article refers to the audio playback using the PCoIP Analog Audio Data Channel from a host machine to a PCoIP Zero Client. It does not apply to microphone input from a PCoIP Zero Client to a VM.   Problem The PCoIP Zero Client must have either an …
Knowledge Base Article Troubleshooting Performance Zero Clients
Last modified: December 20, 2023
1164
Determining why the PCoIP Zero Client was reset to factory default
Problem The PCoIP Zero Client unexpectedly reset to factory default.    Cause The PCoIP Zero Client would only reset to factory defaults if one of the reset options was used. The PCoIP Zero Client can be reset by the PCoIP Management Console, through the …
Knowledge Base Article Troubleshooting Management Management Console Zero Clients
Last modified: September 15, 2023
1093