Why is my display not working correctly when using an adaptor attached to my OEM supplied cable?
Problem After purchasing a HP Anyware product you discover the cable shipped with the HP Anyware product does not have the necessary Video/Display connector to interface with your GPU or monitor. To complete the connection an adaptor is used to change the …
Knowledge Base Article Troubleshooting Display Setup Remote Workstation Card Zero Clients
Last modified: September 14, 2023
865
Can I connect a local monitor to computer that has PCoIP Remote Workstation Card or HP Anyware Installed?
Although you may have enough display heads on your GPU to connect local monitors, it is not a supported configuration when using a PCoIP Remote Workstation Card or HP Anyware. Connecting an additional local monitor may cause the following issues: Blank …
Knowledge Base Article Advisory Display HP Anyware Remote Workstation Card
Last modified: July 31, 2023
851
Why does my screen jitter or stutter, and scroll bars appear on the PCoIP Software client window after connecting to a PCoIP Remote Workstation Card?
Answer: This occurs when a software client is being used on a laptop with the display configured to operate in non-native mode. The EDID information found in some laptops only include timing information for the native display resolution. If a non-native …
Knowledge Base Article Troubleshooting Display Performance Remote Workstation Card
Last modified: January 7, 2024
752
Do PCoIP Zero Clients and PCoIP Remote Workstation Cards support HDMI connections?
PCoIP zero clients only come with the following connections: sVGA DVI (single and dual link) Display Port (1.1a) HDMI is not a supported connector type on PCoIP Zero Clients. You can purchase Display Port or DVI to HDMI cables and adapters however you may …
Knowledge Base Article Advisory Display Setup Remote Workstation Card Zero Clients
Last modified: July 31, 2023
705
What are the possible reasons for jitter on a 30 inch monitor when compared to a 24 inch monitor connected to the same Tera2 Remote Workstation Card?
Problem In a single workstation environment when comparing a 30 inch monitor at 2560x1600 to a 24 inch monitor at 1920x1600, moving a window containing a running video in the 30 inch screen shows latency and window drag when compared to the 24 inch …
Knowledge Base Article Troubleshooting Display Performance Remote Workstation Card
Last modified: December 9, 2022
678
What is the impact of minimum and maximum initial image quality on a PCoIP Session?
Minimum and maximum initial image quality sets the lower and upper quality level. The default values in HP Anyware is Q40 for the minimum initial image quality and Q80 for the maximum initial image quality. If PCoIP estimates there is adequate bandwidth …
Knowledge Base Article Advisory Display Performance Remote Workstation Card HP Anyware
Last modified: July 31, 2023
610
Should I use an initial image quality of Q100?
An initial image quality of Q100 will deliver the highest quality of image PCoIP can deliver. Q100 is not lossless, for a lossless image, build to lossless must be enabled.  How to configure the Turn off Build-to-Lossless feature session variable in GPO …
Knowledge Base Article Advisory Display Performance Remote Workstation Card Zero Clients HP Anyware
Last modified: August 1, 2023
592
Why can't I get 2560x1600 Resolution on my PCoIP Remote Workstation Access Card (Host Card)?
Answer: Due to display changes after PCoIP Remote Workstation Card Firmware 4.2, you need to disable monitor emulation on all nonactive ports on the PCoIP Remote Workstation Card. Note: Dual port PCoIP Remote Workstation Cards support a maximum of one …
Knowledge Base Article Troubleshooting Display Remote Workstation Card
Last modified: November 18, 2022
555
What are the cabling requirements in a Remote Workstation Card environment?
Answer: HP Anyware PCoIP Remote Workstation Cards and PCoIP Zero Clients are designed considering port pass through and should be connected in a specific manner to limit potential display issues. In a PCoIP workstation environment ensure the connection …
Knowledge Base Article Advisory Display Remote Workstation Card
Last modified: August 2, 2023
440
Should I configure "Maximum Initial Image Quality" to 100 if I want lossless still image?
No. Regardless of PCoIP image-quality settings, still images are always lossless. The time it takes to display them depends on your image-quality settings and available network bandwidth. For most situations, it is recommended to use 40 for Minimum Image …
Knowledge Base Article Advisory Performance Display Remote Workstation Card HP Anyware Zero Clients
Last modified: December 9, 2022
356