What are the possible reasons for jitter on a 30 inch monitor when compared to a 24 inch monitor connected to the same Tera2 Remote Workstation Card?
Problem In a single workstation environment when comparing a 30 inch monitor at 2560x1600 to a 24 inch monitor at 1920x1600, moving a window containing a running video in the 30 inch screen shows latency and window drag when compared to the 24 inch …
Knowledge Base Article Troubleshooting Display Performance Remote Workstation Card
Last modified: December 9, 2022
680
What is the impact of minimum and maximum initial image quality on a PCoIP Session?
Minimum and maximum initial image quality sets the lower and upper quality level. The default values in HP Anyware is Q40 for the minimum initial image quality and Q80 for the maximum initial image quality. If PCoIP estimates there is adequate bandwidth …
Knowledge Base Article Advisory Display Performance Remote Workstation Card HP Anyware
Last modified: July 31, 2023
610
Should I use an initial image quality of Q100?
An initial image quality of Q100 will deliver the highest quality of image PCoIP can deliver. Q100 is not lossless, for a lossless image, build to lossless must be enabled.  How to configure the Turn off Build-to-Lossless feature session variable in GPO …
Knowledge Base Article Advisory Display Performance Remote Workstation Card Zero Clients HP Anyware
Last modified: August 1, 2023
595
Why can't I get 2560x1600 Resolution on my PCoIP Remote Workstation Access Card (Host Card)?
Answer: Due to display changes after PCoIP Remote Workstation Card Firmware 4.2, you need to disable monitor emulation on all nonactive ports on the PCoIP Remote Workstation Card. Note: Dual port PCoIP Remote Workstation Cards support a maximum of one …
Knowledge Base Article Troubleshooting Display Remote Workstation Card
Last modified: November 18, 2022
557
What are the cabling requirements in a Remote Workstation Card environment?
Answer: HP Anyware PCoIP Remote Workstation Cards and PCoIP Zero Clients are designed considering port pass through and should be connected in a specific manner to limit potential display issues. In a PCoIP workstation environment ensure the connection …
Knowledge Base Article Advisory Display Remote Workstation Card
Last modified: August 2, 2023
442
Should I configure "Maximum Initial Image Quality" to 100 if I want lossless still image?
No. Regardless of PCoIP image-quality settings, still images are always lossless. The time it takes to display them depends on your image-quality settings and available network bandwidth. For most situations, it is recommended to use 40 for Minimum Image …
Knowledge Base Article Advisory Performance Display Remote Workstation Card HP Anyware Zero Clients
Last modified: December 9, 2022
366
Why do I see black bars on the side or bottom of my display when connecting to a zero client?
Scenario : When connecting a display (TV or monitor) to a PCoIP zero client you get solid black bars at the top and bottom or left and right sides of the display. It appears as if the image is being cut off. Resolution : This issue is caused by ' …
Knowledge Base Article Troubleshooting Display HP Anyware Remote Workstation Card Zero Clients
Last modified: July 15, 2023
325
Profile application to Remote Workstation Card fails
Scenario : The remote workstation card is at a factory default. You set a basic Profile in the management console and apply the Profile. The Profile application fails. If you check the management console, there is no clue as to why the Profile failed. If …
Knowledge Base Article Troubleshooting Management Management Console Remote Workstation Card
Last modified: September 19, 2023
316
What does "MCU not initialized" log message mean?
Problem You are unable to manage a zero client using the HP Anyware PCoIP Management Console 1.x (MC). The event logs reveal the following MCU errors: LVL:1 RC:-500        MCU :(tera_mcu_read_eeprom_bit): Cannot read from EEPROM, MCU not initialized. …
Knowledge Base Article Troubleshooting Management Remote Workstation Card Zero Clients
Last modified: September 19, 2023
278
Management Console profile is not applied to the Remote Workstation Card
Applying a Profile to a Remote Workstation Card from PCoIP Management Console will be unsuccessful if the Enable Audio setting on the Remote Workstation Card has never been enabled (default is disabled) or the Remote Workstation Card has not had the …
Knowledge Base Article Troubleshooting Management Management Console Remote Workstation Card
Last modified: November 8, 2020
226