Why does the "Source signal on other port" message appear on my display?
This indicates that a video source connected to the Host does not correspond with the video port used on the PCoIP Zero Client. This can be corrected by either swapping the video ports used on the Host or the PCoIP Zero Client. The following shows two …
Knowledge Base Article Advisory Display Remote Workstation Card Zero Clients
Last modified: September 3, 2023
4909
Linux DHCP server configuration when using DHCP Discovery on PCoIP Management Console 2.x and 3.x
Answer: This is based on PCoIP Management Console 2.x and newer only This is an example of configuring a Linux DHCP server when using DHCP Option for device discovery. The DHCP server is configured by editing the configuration file: /etc/dhcpd.conf This …
Knowledge Base Article Tutorial Management Setup Management Console
Last modified: January 25, 2024
4550
Host Display Health Check - Diagnostics and troubleshooting guide
Summary To receive a detailed host diagnostic report, create a host agent  support/log file bundle  and then submit this bundle to the PCoIP  health check   tool.  Once the files are submitted, it will take 5-10 minutes to produce a detailed report.  The …
Knowledge Base Article Diagnostics Display HP Anyware Remote Workstation Card
Last modified: September 3, 2023
4198
What causes a firmware upgrade failure?
Problem Uploading firmware through the AWI or a PCoIP Zero Client or PCoIP Remote Workstation Card fails with an error message. Applying firmware through the PCoIP Management Console fails.   Cause and Solution There are multiple scenarios that can cause …
Knowledge Base Article Troubleshooting Setup Management Remote Workstation Card Zero Clients
Last modified: September 3, 2023
4002
How can I change USB authorizations for PCoIP Zero Client?
USB devices can be enabled or disabled which allows IT control of the use of peripherals with HP Anyware PCoIP Agent, VMware Horizon View using PCoIP protocol, or PCoIP Remote Workstation Cards. PCoIP Zero Clients provide unique USB security features that …
Knowledge Base Article Tutorial Management Peripheral Devices Security Remote Workstation Card Zero Clients
Last modified: September 3, 2023
3874
PCoIP display is 'blurry' and the image is of lower than expected quality
Problem When using PCoIP the display is 'blurry' or of low quality. The display may be persistently blurry or is blurry intermittently and slow.    Cause Typically a blurry screen is due to the lack of bandwidth. Throughout a PCoIP session, PCoIP network …
Knowledge Base Article Troubleshooting Performance Display Remote Workstation Card Zero Clients HP Anyware
Last modified: September 3, 2023
3867
What does the 'No source signal' message mean?
The answer depends on what type of host the PCoIP Zero Client is connected to.  VMware View 4.5 or newer The message "no source signal" appears as an overlay when the VMware View virtual desktop puts the monitors to sleep.  Pressing a key or moving the …
Knowledge Base Article Troubleshooting Display HP Anyware Remote Workstation Card Zero Clients
Last modified: September 3, 2023
3616
What are the supported monitor resolutions and refresh rates for PCoIP Zero Clients and Remote Workstation Cards?
In general, PCoIP zero clients and Remote Workstation cards should work with standard display resolutions supported by VESA. The following is a list of the tested monitor resolutions supported (display timing); all at 60 Hz display refresh rate. …
Knowledge Base Article Advisory Display Remote Workstation Card Zero Clients
Last modified: September 3, 2023
3583
How do I Set Zero Client password in PCoIP Management Console?
Use PCoIP Management Console PCoIP Management Console is recommended to manage the password setup for zero clients, including enabling the password protection for OSD and AWI, setting the password, and whether or not hiding the Password options from OSD …
Knowledge Base Article Tutorial Authentication Management Management Console Zero Clients
Last modified: September 3, 2023
3120
Why do I get a gray screen when connecting from the HP Anyware PCoIP Software Client to a PCoIP Remote Workstation Card?
Answer: To resolve this issue, please make sure that you have the following installed and set correctly on the host PC/workstation - i.e. a computer with a PCoIP Remote Workstation Card (host card) installed: The host card should be running PCoIP firmware …
Knowledge Base Article Troubleshooting Display Remote Workstation Card
Last modified: September 3, 2023
2747