Troubleshooting artifacts in a PCoIP Session
Problem During a PCoIP Session artifacts are appearing on the screen. The artifacts may stay or slowly disappear.   Cause and Resolution There are may reasons artifacts may appear on the screen. Some may be source issues such as the application or …
Knowledge Base Article Troubleshooting Performance Display HP Anyware Remote Workstation Card Zero Clients
Last modified: September 3, 2023
1555
Why is the BIOS not visible when my Dell workstation boots with a PCoIP Remote Workstation Card?
Scenario The BIOS on a Dell R5500/R5400 is not visible on boot up. After the OS loads, the monitor then displays the desktop. On some graphic cards, only the primary port is active during the POST phase of the host PC boot process. For example, when using …
Knowledge Base Article Troubleshooting Setup Display Remote Workstation Card
Last modified: September 3, 2023
1505
Mirroring displays on PCoIP Zero Clients
Requirements Tera2 dual port client (TERA2321) Firmware 4.1 or newer   Instructions From the PCoIP Zero Client's onscreen display (OSD) or both versions of the Management Console OSD - browse to Options > Configuration > Display > Enable Display Cloning …
Knowledge Base Article Tutorial Display Zero Clients
Last modified: November 7, 2022
1246
Getting blank screen or "source signal on other port" when connecting from zero client to VMware Horizon
Scenario: When using a PCoIP zero client connecting to VMware VM running Horizon Agent 8.2 if the VMware remote console is open while user is in session the zero client will display a blank screen or you may receive a message "source signal on other …
Knowledge Base Article Troubleshooting Display Third Party Enhancements Zero Clients
Last modified: September 3, 2023
1232
Displays
After completing this unit, you’ll be able to: Understand the different display configurations. Understand the supported resolutions 20 mins With PCoIP, you can configure several display settings as described below.   Display Resolutions PCoIP supports …
Knowledge Base Article Tutorial Display HP Anyware
Last modified: September 5, 2023
1165
When connecting to the PCoIP Graphics Agent I only get 1 display when I have 2 or more connected
Problem When connecting to a PCoIP Graphics Agent installed on a machine with an Nvidia GRID K340, Nvidia GRID K520, Nvidia GRID M series or above GPU I only get one display but the PCoIP Zero Client or PCoIP Software Client has multiple displays …
Knowledge Base Article Troubleshooting Display HP Anyware
Last modified: November 16, 2022
1096
Why does my screen jitter or stutter, and scroll bars appear on the PCoIP Software client window after connecting to a PCoIP Remote Workstation Card?
Answer: This occurs when a software client is being used on a laptop with the display configured to operate in non-native mode. The EDID information found in some laptops only include timing information for the native display resolution. If a non-native …
Knowledge Base Article Troubleshooting Display Performance Remote Workstation Card
Last modified: January 7, 2024
767
Why does the dual-link DVI monitor connected to my PCoIP Zero Client not display properly?
Check your DVI cable, it may not be dual-link capable. Dual-link cable ends have all of the pins populated whereas single-link cables are missing 6 pins. These pins carry the extra information to allow up to 2560 x 1600 resolution. Some monitors will …
Knowledge Base Article Troubleshooting Display Zero Clients
Last modified: November 22, 2022
698
What are the possible reasons for jitter on a 30 inch monitor when compared to a 24 inch monitor connected to the same Tera2 Remote Workstation Card?
Problem In a single workstation environment when comparing a 30 inch monitor at 2560x1600 to a 24 inch monitor at 1920x1600, moving a window containing a running video in the 30 inch screen shows latency and window drag when compared to the 24 inch …
Knowledge Base Article Troubleshooting Display Performance Remote Workstation Card
Last modified: December 9, 2022
689