Tera 2 PCoIP Zero Client and PCoIP Remote Workstation Card firmware prerequisites when upgrading to new firmware releases.
Answer Depending on the currently installed firmware version on your Tera2 device, an upgrade to new firmware may require an intermediate firmware upload. To upgrade the PCoIP Zero Client and PCoIP Remote Workstation Card firmware, follow the associated …
Knowledge Base Article Troubleshooting Management Setup Remote Workstation Card Zero Clients
Last modified: September 3, 2023
12240
Why has my PCoIP Client display temporarily shown a black screen?
Scenario While in a PCoIP session, the display(s) temporarily go black for a few seconds (typically 1-5 seconds) and then resumes normal operation. Occasionally the screen may be briefly frozen instead of turning black.   Cause This entry signifies that …
Knowledge Base Article Troubleshooting Performance Display HP Anyware Zero Clients
Last modified: September 13, 2023
8233
PCoIP TROUBLESHOOTING STEPS: VMware View Virtual desktop performance
This article provides a brief list of general troubleshooting steps for performance issues on virtual desktops. Scenarios covered include: Video slicing or tearing. Screen (or parts of the screen) becomes fuzzy screen and then clears up. Slow screen …
Knowledge Base Article Troubleshooting Performance Display Third Party Enhancements HP Anyware Remote Workstation Card
Last modified: September 3, 2023
8009
Why does the "Source signal on other port" message appear on my display?
This indicates that a video source connected to the Host does not correspond with the video port used on the PCoIP Zero Client. This can be corrected by either swapping the video ports used on the Host or the PCoIP Zero Client. The following shows two …
Knowledge Base Article Advisory Display Remote Workstation Card Zero Clients
Last modified: September 3, 2023
4883
Linux DHCP server configuration when using DHCP Discovery on PCoIP Management Console 2.x and 3.x
Answer: This is based on PCoIP Management Console 2.x and newer only This is an example of configuring a Linux DHCP server when using DHCP Option for device discovery. The DHCP server is configured by editing the configuration file: /etc/dhcpd.conf This …
Knowledge Base Article Tutorial Management Setup Management Console
Last modified: January 25, 2024
4503
Using a custom display resolution and the Hot Plug Reset function on a PCoIP Zero Client
Setting a custom display resolution A PCoIP Zero Client allows you to set a custom display resolution on the client, which is saved even when the client is powered down. This lets you set a resolution that is different than the attached display's native …
Knowledge Base Article Tutorial Setup Display Zero Clients
Last modified: September 3, 2023
4119
What causes a firmware upgrade failure?
Problem Uploading firmware through the AWI or a PCoIP Zero Client or PCoIP Remote Workstation Card fails with an error message. Applying firmware through the PCoIP Management Console fails.   Cause and Solution There are multiple scenarios that can cause …
Knowledge Base Article Troubleshooting Setup Management Remote Workstation Card Zero Clients
Last modified: September 3, 2023
3951
PCoIP display is 'blurry' and the image is of lower than expected quality
Problem When using PCoIP the display is 'blurry' or of low quality. The display may be persistently blurry or is blurry intermittently and slow.    Cause Typically a blurry screen is due to the lack of bandwidth. Throughout a PCoIP session, PCoIP network …
Knowledge Base Article Troubleshooting Performance Display Remote Workstation Card Zero Clients HP Anyware
Last modified: September 3, 2023
3828
What does the 'No source signal' message mean?
The answer depends on what type of host the PCoIP Zero Client is connected to.  VMware View 4.5 or newer The message "no source signal" appears as an overlay when the VMware View virtual desktop puts the monitors to sleep.  Pressing a key or moving the …
Knowledge Base Article Troubleshooting Display HP Anyware Remote Workstation Card Zero Clients
Last modified: September 3, 2023
3555
What are the supported monitor resolutions and refresh rates for PCoIP Zero Clients and Remote Workstation Cards?
In general, PCoIP zero clients and Remote Workstation cards should work with standard display resolutions supported by VESA. The following is a list of the tested monitor resolutions supported (display timing); all at 60 Hz display refresh rate. …
Knowledge Base Article Advisory Display Remote Workstation Card Zero Clients
Last modified: September 3, 2023
3537