Should I configure "Maximum Initial Image Quality" to 100 if I want lossless still image?
No. Regardless of PCoIP image-quality settings, still images are always lossless. The time it takes to display them depends on your image-quality settings and available network bandwidth. For most situations, it is recommended to use 40 for Minimum Image …
Knowledge Base Article Advisory Performance Display Remote Workstation Card HP Anyware Zero Clients
Last modified: December 9, 2022
385
PCoIP TROUBLESHOOTING STEPS: IEEE 802.1x Network Authentication
This article provides a brief list of troubleshooting steps for common issues with 802.1x authentication. It is not intended to be a comprehensive troubleshooting guide. These include scenarios for: Problems uploading IEEE 802.1x certificates to PCoIP …
Knowledge Base Article Troubleshooting Security Remote Workstation Card Zero Clients
Last modified: September 7, 2023
384
What does "IPC: Frame encode took xxx ms so far. Dropping down the quality to index x." in the log files indicate?
Answer: In this case, the imaging encoder has determined that too many bits were being sent in the upper portion of the frame (i.e. flooding) which causes the frame to take longer to encode, and therefore appears unresponsive to the user (> 750 ms to …
Knowledge Base Article Troubleshooting Performance HP Anyware Zero Clients Remote Workstation Card
Last modified: December 9, 2022
381
How many hosts are discovered when using SLP Host Discovery?
When using a session connection type setting of  Direct to Host +SLP Host Discovery , the PCoIP Zero Client can discover up to 10 hosts and will display the first 6 identified. The list may change on subsequent sessions.   … How many hosts are discovered …
Knowledge Base Article Advisory Remote Workstation Card Zero Clients
Last modified: September 14, 2023
378
What is Standalone mode?
  Answer: Standalone mode lets a Tera1 PCoIP Remote Workstation Card operate without installation in a PCIe slot. In Standalone mode, the PCoIP Remote Workstation Card is powered from a floppy drive (+5V/+12V) power connector instead of from a PCIe slot. …
Knowledge Base Article Tutorial Remote Workstation Card
Last modified: September 19, 2023
371
Requirements for the Leostream broker to automatically detect a PCoIP Remote Workstation Card?
Requirements For the Leostream broker to automatically detect a Remote Workstation Card the following components must be installed: PCoIP Remote Workstation Card inserted in the host PC Leostream Connection Broker 7.7 or newer Leostream Agent 5.5.95 or …
Knowledge Base Article Tutorial Third Party Enhancements Remote Workstation Card HP Anyware
Last modified: September 19, 2023
369
Skipped compressing pkt due to PCM bit length in the PCoIP Remote Workstation Card Logs
Scenario User notices poor audio quality when connected to a PCoIP Remote Workstation Card (host card), and the following entries are in the PCoIP Remote Workstation Card's logs: 12/04/2013, 00:01:41> LVL:3 RC: 0 AUDIO_CMPRS :Skipped compressing pkt due …
Knowledge Base Article Troubleshooting Performance Remote Workstation Card Zero Clients
Last modified: August 3, 2023
357
After upgrading Windows, why can I no longer wake my PCoIP Remote Workstation Card host from the PCoIP Zero Client?
Wake-on-LAN behaviour changed from Windows 7 to Windows 8, 8.1 and 10, preventing the PCoIP Zero Client from waking the host PC if the PCoIP Zero Client was configured to send the WoL packet to the host PC NIC and not the PCoIP Remote Workstation Card. …
Knowledge Base Article Troubleshooting Remote Workstation Card Zero Clients
Last modified: September 19, 2023
351
Can I enable NTP time on a PCoIP Zero Client or PCoIP Remote Workstation Card using DHCP options?
Answer: Yes. NTP time servers can be added to DHCP options 042 based on IP scope or as a default for all IP scopes. It is important to note that this feature may impact setting the time server by the PCoIP Management Console Profile or the Administrator …
Knowledge Base Article Advisory Remote Workstation Card Zero Clients
Last modified: September 12, 2023
345
Do all log entries marked (CAUTION!) indicate a possible critical issue?
No, log entries marked with (CAUTION!) are not necessarily a critical issue. The case below states such a case but it is still essential to note these log entries could be indicative of a potential issue.   Scenario 1 You see caution errors similar to the …
Knowledge Base Article Advisory Remote Workstation Card Zero Clients
Last modified: September 12, 2023
341