Profile application to Remote Workstation Card fails
Scenario : The remote workstation card is at a factory default. You set a basic Profile in the management console and apply the Profile. The Profile application fails. If you check the management console, there is no clue as to why the Profile failed. If …
Knowledge Base Article Troubleshooting Management Management Console Remote Workstation Card
Last modified: September 19, 2023
325
How long before a PCoIP Management Console certificate expires should I replace it?
Before the PCoIP Management Console certificate can be replaced, the new certificate or the signing root CA certificate must be installed in the PCoIP Zero Client or PCoIP Remote Workstation Card certificate store. Once a PCoIP Endpoint is manged by an …
Knowledge Base Article Advisory Management Security Management Console
Last modified: September 19, 2023
295
Cannot import profile from Management Console 1.x into the PCoIP Management Console 2.x or 3.x
Answer : Importing Profiles from MC 1.x into MC 2.x is supported and documented in the user guide. Refer to the Administrators' guide for the release of the PCoIP Management Console in use. There have been a couple reports of users experiencing an issue …
Knowledge Base Article Troubleshooting Management Management Console
Last modified: September 19, 2023
292
What does "MCU not initialized" log message mean?
Problem You are unable to manage a zero client using the HP Anyware PCoIP Management Console 1.x (MC). The event logs reveal the following MCU errors: LVL:1 RC:-500        MCU :(tera_mcu_read_eeprom_bit): Cannot read from EEPROM, MCU not initialized. …
Knowledge Base Article Troubleshooting Management Remote Workstation Card Zero Clients
Last modified: September 19, 2023
286
Why Imported Profile(s) from PCoIP Management Console 1.x/2.x to PCoIP Management Console 3.x cannot be applied? Status shows skipped.
Scenario Imported a profile from PCoIP Management Console 1.x /2.x  to PCoIP Management Console 3.x where firmware 6.0.0 is the only uploaded version in Settings -> Software. Pushing the profile to PCoIP Zero Clients results in a 'skipped' status.   Cause …
Knowledge Base Article Troubleshooting Management Management Console
Last modified: September 19, 2023
276
Default HP Anyware Connector docker network conflicts with VPN network
Scenario: The default HP Anyware Connector docker network is conflicting with VPN network. When specifying the --connector-network-cidr flag during the installation of HP Anyware Connector the docker network is that same range as the default 172.x How can …
Knowledge Base Article Troubleshooting Management Setup HP Anyware
Last modified: August 7, 2023
272
How can I tell which monitors are connected and if a USB device is connected locally or bridged on a PCoIP Zero Client?
Answer: From your Web browser, enter the IP address of your PCoIP Zero Client. Log in to the user interface with your user credentials. (Note: Depending on your specific setup, a password may not be required.) From the Info menu, select Attached Devices . …
Knowledge Base Article Troubleshooting Display Zero Clients
Last modified: October 31, 2022
263
Why do certain large screen (>27" monitors) dual-link DVI monitors not work with the TERA 2 PCoIP Zero Clients?
Scenario When some monitors supporting 2560 x 1600 and 2560 x 1440 resolutions are power cycled with the power switch, the video may not appear when connected to a Tera2 Zero Client via dual-link DVI. This applies to: Tera2 Zero Clients running firmware …
Knowledge Base Article Troubleshooting Display Zero Clients
Last modified: November 18, 2022
255
How do I change the FQDN (Fully Qualified Domain Name) of a PCoIP Zero Client?
First, change the PCoIP name to a new name. Currently, the "PCoIP Device Name" can only be changed on an individual basis in two locations: The  "OSD--> Configuration--> Label"  tab The  "AWI--> Configuration--> Label"  tab The default format is  …
Knowledge Base Article Advisory Management Management Console Zero Clients
Last modified: September 3, 2023
259