The VMware Horizon View PCoIP server logs show "IPC Can't encode. Waiting. queue" after a random disconnect.
Problem The VMware Horizon View Client or PCoIP Zero Client experience a random disconnect from the VMware Horizon View session. Inspection of the PCoIP server logs show a high slice rate count after a random disconnect. The following example shows 192 …
Knowledge Base Article Troubleshooting Performance Session Third Party Enhancements Zero Clients
Last modified: September 3, 2023
438
Which PCoIP Zero Clients are VMware Ready certified?
For a list of VMware Ready certified PCoIP Zero Clients see VMware View HCL .  Note: PCoIP Zero Clients can be identified by ThreadX in the OS Version column.  For a complete list of PCoIP Zero Clients, see the HP web site . … Which PCoIP Zero Clients are …
Knowledge Base Article Advisory Setup Third Party Enhancements Zero Clients
Last modified: September 3, 2023
417
Should I configure "Maximum Initial Image Quality" to 100 if I want lossless still image?
No. Regardless of PCoIP image-quality settings, still images are always lossless. The time it takes to display them depends on your image-quality settings and available network bandwidth. For most situations, it is recommended to use 40 for Minimum Image …
Knowledge Base Article Advisory Performance Display Remote Workstation Card HP Anyware Zero Clients
Last modified: December 9, 2022
382
Why do I see black bars on the side or bottom of my display when connecting to a zero client?
Scenario : When connecting a display (TV or monitor) to a PCoIP zero client you get solid black bars at the top and bottom or left and right sides of the display. It appears as if the image is being cut off. Resolution : This issue is caused by ' …
Knowledge Base Article Troubleshooting Display HP Anyware Remote Workstation Card Zero Clients
Last modified: July 15, 2023
337
No warning message when VMware View Connection Server Certificate Check Mode is set to Warn if Connection may be insecure (Default)
This is expected behavior. Configured non-interactive session modes do not display VCS Warning messages in Warn if the connection may be insecure (Default) security mode.  Interactive session modes will display VCS Error messages in Warn if the connection …
Knowledge Base Article Troubleshooting Security Third Party Enhancements Zero Clients
Last modified: September 3, 2023
281
In VMware Horizon View, what does it mean when a particular USB issue happens on both the VMware View client and the PCoIP Zero Client?
Answer: If a USB peripheral has the same issue on both PCoIP Zero Clients and VMware View clients (repurposed PC, notebook or thin client running the View Client), it's likely that the issue is in the VMware virtual USB hub driver, or is an issue with …
Knowledge Base Article Troubleshooting Peripheral Devices Third Party Enhancements Zero Clients
Last modified: September 3, 2023
266
Why is the host PC on my VMware Horizon brokered Remote Workstation Solution unable to wake up?
Scenario When a View Connection Server brokers a workstation connection between a PCoIP Zero Client and a PCoIP Remote Workstation Card, and the host is put into any low power state (sleep, hibernate or shutdown); the client is unable to wake the host and …
Knowledge Base Article Troubleshooting Setup Performance Third Party Enhancements Remote Workstation Card Zero Clients
Last modified: September 20, 2023
265
How can I tell which monitors are connected and if a USB device is connected locally or bridged on a PCoIP Zero Client?
Answer: From your Web browser, enter the IP address of your PCoIP Zero Client. Log in to the user interface with your user credentials. (Note: Depending on your specific setup, a password may not be required.) From the Info menu, select Attached Devices . …
Knowledge Base Article Troubleshooting Display Zero Clients
Last modified: October 31, 2022
261
Why do certain large screen (>27" monitors) dual-link DVI monitors not work with the TERA 2 PCoIP Zero Clients?
Scenario When some monitors supporting 2560 x 1600 and 2560 x 1440 resolutions are power cycled with the power switch, the video may not appear when connected to a Tera2 Zero Client via dual-link DVI. This applies to: Tera2 Zero Clients running firmware …
Knowledge Base Article Troubleshooting Display Zero Clients
Last modified: November 18, 2022
255