What does "MCU not initialized" log message mean?
Problem You are unable to manage a zero client using the HP Anyware PCoIP Management Console 1.x (MC). The event logs reveal the following MCU errors: LVL:1 RC:-500        MCU :(tera_mcu_read_eeprom_bit): Cannot read from EEPROM, MCU not initialized. …
Knowledge Base Article Troubleshooting Management Remote Workstation Card Zero Clients
Last modified: September 19, 2023
286
What are the limitations of configuring active directory with Management Console?
PCoIP Management Console 3.2.x has important limitations which need to be considered before using this feature in your deployment.   Active Directory users must be assigned to a Security Group. Only supports one active domain at a time. Does not support …
Knowledge Base Article Advisory Setup Management Console
Last modified: April 10, 2019
279
Why Imported Profile(s) from PCoIP Management Console 1.x/2.x to PCoIP Management Console 3.x cannot be applied? Status shows skipped.
Scenario Imported a profile from PCoIP Management Console 1.x /2.x  to PCoIP Management Console 3.x where firmware 6.0.0 is the only uploaded version in Settings -> Software. Pushing the profile to PCoIP Zero Clients results in a 'skipped' status.   Cause …
Knowledge Base Article Troubleshooting Management Management Console
Last modified: September 19, 2023
276
Default HP Anyware Connector docker network conflicts with VPN network
Scenario: The default HP Anyware Connector docker network is conflicting with VPN network. When specifying the --connector-network-cidr flag during the installation of HP Anyware Connector the docker network is that same range as the default 172.x How can …
Knowledge Base Article Troubleshooting Management Setup HP Anyware
Last modified: August 7, 2023
272
How do I configure wake-on-LAN with the AMD R5000 PCoIP Remote Workstation Card?
There are three ways to configure wake-on-LAN with the AMD R5000 PCoIP Remote Workstation Card. Option 1: Use the PC NIC and PCoIP Host Software  For instructions, refer to How do I remotely power on the host PC/workstation through its network interface …
Knowledge Base Article Tutorial Setup Remote Workstation Card
Last modified: August 23, 2018
265
Why is the host PC on my VMware Horizon brokered Remote Workstation Solution unable to wake up?
Scenario When a View Connection Server brokers a workstation connection between a PCoIP Zero Client and a PCoIP Remote Workstation Card, and the host is put into any low power state (sleep, hibernate or shutdown); the client is unable to wake the host and …
Knowledge Base Article Troubleshooting Setup Performance Third Party Enhancements Remote Workstation Card Zero Clients
Last modified: September 20, 2023
265
How can I tell which monitors are connected and if a USB device is connected locally or bridged on a PCoIP Zero Client?
Answer: From your Web browser, enter the IP address of your PCoIP Zero Client. Log in to the user interface with your user credentials. (Note: Depending on your specific setup, a password may not be required.) From the Info menu, select Attached Devices . …
Knowledge Base Article Troubleshooting Display Zero Clients
Last modified: October 31, 2022
263
How do I change the FQDN (Fully Qualified Domain Name) of a PCoIP Zero Client?
First, change the PCoIP name to a new name. Currently, the "PCoIP Device Name" can only be changed on an individual basis in two locations: The  "OSD--> Configuration--> Label"  tab The  "AWI--> Configuration--> Label"  tab The default format is  …
Knowledge Base Article Advisory Management Management Console Zero Clients
Last modified: September 3, 2023
258
Why do certain large screen (>27" monitors) dual-link DVI monitors not work with the TERA 2 PCoIP Zero Clients?
Scenario When some monitors supporting 2560 x 1600 and 2560 x 1440 resolutions are power cycled with the power switch, the video may not appear when connected to a Tera2 Zero Client via dual-link DVI. This applies to: Tera2 Zero Clients running firmware …
Knowledge Base Article Troubleshooting Display Zero Clients
Last modified: November 18, 2022
255
Why my HP anyware Connector (CACv2) does not connect after the recent Ubuntu 18.04 OS Nov-13-2019 Update?
The latest patch release of Ubuntu 18.04 (Nov-13 patch) will break CAM CACv2 connectivity. Affected Ubuntu 18.04 OS patch version: Nov-13-2019 release:  ubuntu-1804-bionic-v20191113 ubuntu-os-cloud ubuntu-1804-lts Recommendation: If you experience this …
Knowledge Base Article Tutorial Management HP Anyware
Last modified: September 19, 2023
253