Do PCoIP Zero Clients and PCoIP Remote Workstation Cards support HDMI connections?
PCoIP zero clients only come with the following connections: sVGA DVI (single and dual link) Display Port (1.1a) HDMI is not a supported connector type on PCoIP Zero Clients. You can purchase Display Port or DVI to HDMI cables and adapters however you may …
Knowledge Base Article Advisory Display Setup Remote Workstation Card Zero Clients
Last modified: July 31, 2023
727
What are the possible reasons for jitter on a 30 inch monitor when compared to a 24 inch monitor connected to the same Tera2 Remote Workstation Card?
Problem In a single workstation environment when comparing a 30 inch monitor at 2560x1600 to a 24 inch monitor at 1920x1600, moving a window containing a running video in the 30 inch screen shows latency and window drag when compared to the 24 inch …
Knowledge Base Article Troubleshooting Display Performance Remote Workstation Card
Last modified: December 9, 2022
693
Can I use both DHCP options and DNS SRV records for device discovery in the PCoIP Management Console at the same time?
Answer: No . Note: It is recommended to user either DHCP Options or DNS Records when configuring auto-discovery for the PCoIP Management Console. To determine which to use you need to understand your environment. For example if you are only going to have …
Knowledge Base Article Advisory Management Management Console
Last modified: September 7, 2023
680
Installing Management Console
After completing this unit, you’ll be able to: Install the HP Anyware Management Console, or Migrate to a newer version 25 mins   HP Anyware Management Console is released in three formats that feature CentOS as the PCoIP Management Console installation …
Knowledge Base Article Tutorial Management Setup Management Console
Last modified: August 2, 2023
668
My PCoIP Zero Clients at the remote location cannot connect to PCoIP Management Console 3.x
Problem PCoIP Zero Clients in remote locations are not connecting to the PCoIP Management Console 3.x   Cause This issue was tracked down to a setting in the PCoIP Management Console 3.x (MC). Check under Settings > Remote and confirm if you have entered …
Knowledge Base Article Troubleshooting Management Management Console
Last modified: November 7, 2022
665
What is the impact of minimum and maximum initial image quality on a PCoIP Session?
Minimum and maximum initial image quality sets the lower and upper quality level. The default values in HP Anyware is Q40 for the minimum initial image quality and Q80 for the maximum initial image quality. If PCoIP estimates there is adequate bandwidth …
Knowledge Base Article Advisory Display Performance Remote Workstation Card HP Anyware
Last modified: July 31, 2023
625
Should I use an initial image quality of Q100?
An initial image quality of Q100 will deliver the highest quality of image PCoIP can deliver. Q100 is not lossless, for a lossless image, build to lossless must be enabled.  How to configure the Turn off Build-to-Lossless feature session variable in GPO …
Knowledge Base Article Advisory Display Performance Remote Workstation Card Zero Clients HP Anyware
Last modified: August 1, 2023
610
How do I disable login username caching on a PCoIP Zero Client?
On a PCoIP Zero Client, username caching is set in the advanced options and can be disabled from the OSD Screen, the Administrative Web Interface (AWI), or the PCoIP Management Console.    From the OSD Screen: Under Options, select Configuration In the …
Knowledge Base Article Tutorial Setup Management Session Management Console Zero Clients
Last modified: September 3, 2023
593
Why can't I get 2560x1600 Resolution on my PCoIP Remote Workstation Access Card (Host Card)?
Answer: Due to display changes after PCoIP Remote Workstation Card Firmware 4.2, you need to disable monitor emulation on all nonactive ports on the PCoIP Remote Workstation Card. Note: Dual port PCoIP Remote Workstation Cards support a maximum of one …
Knowledge Base Article Troubleshooting Display Remote Workstation Card
Last modified: November 18, 2022
576
Sample CentOS 7.4 DHCP configuration file for PCoIP Management Console auto discovery
The purpose of this tutorial is to provide a sample DHCP configuration for auto discovery of the PCoIP Management Console 2.x and newer. In this set up the following were deployed: CentOS 7.4 VM hosted on ESXi 5.5 server. Configured the CentOS VM with two …
Knowledge Base Article Tutorial Management Management Console
Last modified: December 11, 2018
576